A NEW VERSION OF PREPARATORY AND CUTTING WORKS AT THE SHAHOUMIAN GOLD-POLYMETALLIC DEPOSIT

T.S. AGHAMYAN; P.N. NERSISYAN

A NEW VERSION OF PREPARATORY AND CUTTING WORKS AT THE SHAHOUMIAN GOLD-POLYMETALLIC DEPOSIT

Authors

T.S. AGHAMYAN National Polytechnic University of Armenia Author
P.N. NERSISYAN National Polytechnic University of Armenia Author

Keywords:

polymetallic deposit, preparatory and cutting roadways, sinking

Abstract

The preparatory and cutting works carried out at the Shahoumian gold-polymetallic deposit are investigated. While carriyng out these works, it is necessary to reduce the cross-sectional area of the roadway to reduce the ore dislution factor.

Downloads

pdf

Published

18.04.2026

Issue

Vol. 2 (2019)

Section

Articles

Most read articles by the same author(s)

A.A. AYVAZYAN, T.S. AGHAMYAN, H.V. AVAGYAN, THE MECHANISM AND KINETICS OF PHYSICAL AND CHEMICAL PROCESSES PROCEEDING AT ORE CRUSHING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)

Similar Articles

A.M. ZAKARYAN, R.L. ATOYAN, WAYS OF IMPROVING THE DEVELOPMENT SYSTEM APPLIED IN THE SHAHUMAN GOLD POLYMETALLIC DEPOSIT , Proceedings of Annual Conferences of NPUA: Vol. 2 (2018)
A.M. ARZUMANYAN, T.A. MIRVELYAN, CALCULATION OF CUTTING STRENGTH AT PROCESSING OF ALLOYS FROM NON-FERROUS METALS BY CORUNDUM CUTTING PLATES WITH SQUARE-CUTTING CUTTING LOOP , Proceedings of Annual Conferences of NPUA: Vol. 2 (2018)
L.H. MUTAFYAN, R.E. AVAGYAN, THE IMPACT OF THE CUTTING CONDITIONS ON THE CUTTING TOOL WEAR AT TREATING HARD-PROCESSED MATERIALS AT INTERRUPTED CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
H.B. BAGHDASARYAN , M.Y. HARUTYUNYAN, V.H. BAGHDASARYAN , IMPACT OF CUTTING MODES ON THE FORMATION OF TECHNOLOGICAL RESIDUAL STRESSES AT BLADE CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
B.A. BALASANYAN, A.L. ARSHAKYAN, S.H. HAKOBYAN, B.S. BALASANYAN, A PROGRAM FOR CALCULATING THE CUTTING DEPTHS OF THE STAGES OF A MULTI-STAGE DRILL FROM THE EQUALITY CONDITION OF THE PRODUCTS OF THEIR TORQUES AND AXIAL FORCES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2023)
D.G. YURMUZYAN, G.A. SIMONYAN, INVESTIGATING THE CUTTING PROCESS WITH A MULTISTEPPED BLADE CUTTER THROUGH THREE-DIMENSIONAL MODELING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
H.A. ISUNTS, B.S. BALASANYAN, A FIXTURE FOR THE CUTTING EDGE SHARPENING OF A TWIST DRILL WITH A MULTISTAGE BLADE , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
H.A. ISUNTS, MODELING A NEW CONSTRUCTION OF A FIXTURE FOR SHARPENING THE CUTTING EDGES OF A TWIST DRILL , Proceedings of Annual Conferences of NPUA: Vol. 1 (2022)
M.H. SAHAKYAN, H.S. SARAFYAN, ESTIMATION OF ECONOMIC EFFICIENCY OF INNOVATIVE TECHNOLOGIES IN GARMENT PRODUCTION CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
M.H. KHACHATRYAN, T.R. AVAGYAN, THE TECHNICAL PROPERTIES OF COPPER AND ZINC EXTRACTION FROM POLYMETALLIC CONCENTRATES OF THE KAPAN MINING AND DRESSING PLANT BY THE ENRICHMENT METHOD , Proceedings of Annual Conferences of NPUA: Vol. 2 (2019)

1-10 of 38 Next

You may also start an advanced similarity search for this article.

A NEW VERSION OF PREPARATORY AND CUTTING WORKS AT THE SHAHOUMIAN GOLD-POLYMETALLIC DEPOSIT

Authors

Keywords:

Abstract

Downloads

Published

Issue

Section

Most read articles by the same author(s)

Similar Articles

edtor