INVESTIGATING THE CUTTING PROCESS WITH A MULTISTEPPED BLADE CUTTER THROUGH THREE-DIMENSIONAL MODELING

D.G. YURMUZYAN; G.A. SIMONYAN

INVESTIGATING THE CUTTING PROCESS WITH A MULTISTEPPED BLADE CUTTER THROUGH THREE-DIMENSIONAL MODELING

Authors

D.G. YURMUZYAN National Polytechnic University of Armenia Author
G.A. SIMONYAN National Polytechnic University of Armenia Author

Keywords:

multistepped cutter, three-dimensional modeling, cutting process, experimental stand, vibration, cutting zone temperature, metal cutting

Abstract

The research technique of metal cutting with a multistepped cutter through three-dimensional modeling is considered. With the help of the software package 3D Deform methods of modeling of the cutting process are selected.

Downloads

pdf

Published

29.06.2026

Issue

Vol. 2 (2017)

Section

Articles

Most read articles by the same author(s)

B.A. BALASANYAN, H.A. HOVHANNISYAN, A.R. KARAPETYAN, D.G. YURMUZYAN, DEVELOPTNG THE TECHNICAL TASK OF A SMALL-DIMENSION DESKTOP MANIPULATOR BY USING ADDITIVE TECHNOLOGIES AND RAPID PROTOTYPING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2019)

Similar Articles

H.S. MANUKYAN, A.M. ARZUMANYAN, IMPROVING THE OPERATION CHARACTERISTICS AT THIN-BLADЕ PROCESSING WITH MULTI-TOOTH CORUNDUM MILLERS , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
S.S. MARTIROSYAN, COMPREHENSIVE EVALUATION OF POLYGRAPHIC PRINTING FACTORS AND PRODUCTION OF HIGH QUALITY PRINTING , Proceedings of Annual Conferences of NPUA: Vol. 1 (2022)
L.H. MUTAFYAN, R.E. AVAGYAN, THE IMPACT OF THE CUTTING CONDITIONS ON THE CUTTING TOOL WEAR AT TREATING HARD-PROCESSED MATERIALS AT INTERRUPTED CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
H.A. ISUNTS, MODELING A NEW CONSTRUCTION OF A FIXTURE FOR SHARPENING THE CUTTING EDGES OF A TWIST DRILL , Proceedings of Annual Conferences of NPUA: Vol. 1 (2022)
M.M. SIMONYAN, V.R. GEVORGYAN, THE IMPACT AND SOME WAVE PHENOMENA AT METAL CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
B.A. BALASANYAN, A METHOD FOR DETERMINING THE OPTIMAL DIMENSIONS OF A TWO-STAGE DRILL , Proceedings of Annual Conferences of NPUA: Vol. 1 (2022)
G.H. ASCHYAN, T.Sh. TADEVOSYAN, DEVELOPING A TECHNOLOGY FOR OBTAINING ASBESTOS-FREE BRAKE PADS WITH REQUIRED FUNCTIONAL PROPERTIES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2025)
L.A. MANUKYAN, A.A. GHAZARYAN, G.H. GHAZARYAN, SELECTION OF SENSORS FOR STRESS REGISTRATION AT THREE-DIMENSIONAL MODELING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2019)
G.S. YESAFYAN, MODELING AND RESEARCH OF THE SUSPENSION OF A FOUR-WHEEL CAR , Proceedings of Annual Conferences of NPUA: Vol. 1 (2023)
S.G. HAYRAPETYAN, V.H. MARTIROSYAN, O.P. GALSTYAN, INVESTIGATING THE EXTRACTION OF NOBLE METALS CONTAINED IN CARBON ORES BY THE METALLOTHERMIC METHOD , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)

1-10 of 340 Next

You may also start an advanced similarity search for this article.

INVESTIGATING THE CUTTING PROCESS WITH A MULTISTEPPED BLADE CUTTER THROUGH THREE-DIMENSIONAL MODELING

Authors

Keywords:

Abstract

Downloads

Published

Issue

Section

Most read articles by the same author(s)

Similar Articles

edtor