IMPACT OF CUTTING MODES ON THE FORMATION OF TECHNOLOGICAL RESIDUAL STRESSES AT BLADE CUTTING

Authors

H.B. BAGHDASARYAN National Polytechnic University of Armenia Author
M.Y. HARUTYUNYAN National Polytechnic University of Armenia Author
V.H. BAGHDASARYAN National Polytechnic University of Armenia Author

Keywords:

blade cutting, cutting parameters, residual stresses, cutting temperature

Abstract

Issues on the impact of cutting modes on the formation of technological residual stresses in the subsurface layer at blade processing are considered. A brief analysis of the research results is carried out, appointment recommendations on the cutting modes are given at which in the subsurface layer, compressing residual stresses are accumulated.

Downloads

pdf

Published

29.06.2026

Issue

Section

Articles

Similar Articles

D.G. YURMUZYAN, G.A. SIMONYAN, INVESTIGATING THE CUTTING PROCESS WITH A MULTISTEPPED BLADE CUTTER THROUGH THREE-DIMENSIONAL MODELING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
H.S. MANUKYAN, A.M. ARZUMANYAN, IMPROVING THE OPERATION CHARACTERISTICS AT THIN-BLADЕ PROCESSING WITH MULTI-TOOTH CORUNDUM MILLERS , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
A.M. ARZUMANYAN, T.A. MIRVELYAN, CALCULATION OF CUTTING STRENGTH AT PROCESSING OF ALLOYS FROM NON-FERROUS METALS BY CORUNDUM CUTTING PLATES WITH SQUARE-CUTTING CUTTING LOOP , Proceedings of Annual Conferences of NPUA: Vol. 2 (2018)
L.H. MUTAFYAN, R.E. AVAGYAN, THE IMPACT OF THE CUTTING CONDITIONS ON THE CUTTING TOOL WEAR AT TREATING HARD-PROCESSED MATERIALS AT INTERRUPTED CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
B.A. BALASANYAN, A.L. ARSHAKYAN, S.H. HAKOBYAN, B.S. BALASANYAN, A PROGRAM FOR CALCULATING THE CUTTING DEPTHS OF THE STAGES OF A MULTI-STAGE DRILL FROM THE EQUALITY CONDITION OF THE PRODUCTS OF THEIR TORQUES AND AXIAL FORCES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2023)
A.S. PETROSYAN, V.S. GUKASYAN, L.Z. GALSTYAN, ESTIMATION OF RESIDUAL POROSITY IN COMPACT PRODUCTS OBTAINED IN THE TECHNOLOGICAL PROCESS OF EXTRUSION OF POWDER METALLIC MATERIALS , Proceedings of Annual Conferences of NPUA: Vol. 2 (2019)
H.A. ISUNTS, B.S. BALASANYAN, A FIXTURE FOR THE CUTTING EDGE SHARPENING OF A TWIST DRILL WITH A MULTISTAGE BLADE , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
B.A. BALASANYAN, H.A. HOVHANNISYAN, A.L. ARSHAKYAN, A.B. BALASANYAN, A SPIRAL DRILL WITH A MULTI-STAGE BLADE , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
B.A. BALASANYAN, H.A. HOVHANNISYAN, A.B. BALASANYAN, A.L. ARSHAKYAN, A METHOD FOR MAKING A SPIRAL DRILL WITH A MULTI-STAGE BLADE , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
M.G. STAKYAN, M.S. TOROSYAN, H.A. GHAZARYAN, MODERN TECHNOLOGIES OF STRENGTHENING THE WELDED SEAMS OF THIN -WALL PIPELINES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2021)

1-10 of 153 Next

You may also start an advanced similarity search for this article.