WAYS FOR DEVELOPING MACHINES FOR QUARRYING STONE OF THE CORRECT FORM

Authors

J.A. ASATRYAN National Polytechnic University of Armenia Author

Keywords:

quarrying, wall stone wheel machine, circular saw, cutting head

Abstract

The perspectives of developing a technology and machines for quarrying wall stone of the correct form are considered. The critical analysis of three ways is given: The modernization of the quarrying machine CMP-026/1; the technology and machines for quarrying stone by ultra- high pressure water jet, and new wheel quarrying machines.

Downloads

pdf

Published

18.04.2026

Issue

Section

Articles

Most read articles by the same author(s)

J.A. ASATRYAN, S.S. HARUTYUNYAN, F.A. MSRYAN, A.V. BAGHDASARYAN , TECHNOLOGICAL OPPORTUNITIES FOR THE SECONDARY USE OF ABANDONED QUARRIES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2021)
S.S.. HARUTYUNYAN, J.A. ASATRYAN, OPTIMAL CONSTRUCTION OF А WHELLED MACHINE FOR QUARRYING WALL STONE OF THE CORRECT FORM , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)

Similar Articles

S.S.. HARUTYUNYAN, J.A. ASATRYAN, OPTIMAL CONSTRUCTION OF А WHELLED MACHINE FOR QUARRYING WALL STONE OF THE CORRECT FORM , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
J.A. ASATRYAN, S.S. HARUTYUNYAN, F.A. MSRYAN, A.V. BAGHDASARYAN , TECHNOLOGICAL OPPORTUNITIES FOR THE SECONDARY USE OF ABANDONED QUARRIES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2021)
M.G. STAKYAN, N.V. PIRUMYAN, A.V. MARTIROSYAN, APPLICATION OF A HARDENING FINISHING DEVICE IN WELDED JOINTS OF ITINERARY GAS TRANSMISSION PIPELINES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2023)
A.M. ARZUMANYAN, T.A. MIRVELYAN, CALCULATION OF CUTTING STRENGTH AT PROCESSING OF ALLOYS FROM NON-FERROUS METALS BY CORUNDUM CUTTING PLATES WITH SQUARE-CUTTING CUTTING LOOP , Proceedings of Annual Conferences of NPUA: Vol. 2 (2018)
L.H. MUTAFYAN, R.E. AVAGYAN, THE IMPACT OF THE CUTTING CONDITIONS ON THE CUTTING TOOL WEAR AT TREATING HARD-PROCESSED MATERIALS AT INTERRUPTED CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
B.A. BALASANYAN, A.L. ARSHAKYAN, S.H. HAKOBYAN, B.S. BALASANYAN, A PROGRAM FOR CALCULATING THE CUTTING DEPTHS OF THE STAGES OF A MULTI-STAGE DRILL FROM THE EQUALITY CONDITION OF THE PRODUCTS OF THEIR TORQUES AND AXIAL FORCES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2023)
H.B. BAGHDASARYAN , M.Y. HARUTYUNYAN, V.H. BAGHDASARYAN , IMPACT OF CUTTING MODES ON THE FORMATION OF TECHNOLOGICAL RESIDUAL STRESSES AT BLADE CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
D.G. YURMUZYAN, G.A. SIMONYAN, INVESTIGATING THE CUTTING PROCESS WITH A MULTISTEPPED BLADE CUTTER THROUGH THREE-DIMENSIONAL MODELING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
A.R. HOVHANNISYAN, A.R. KOSTANDIAN, N.K. MANASYAN, CIRCULAR ECONOMY IN THE CONTEXT OF INVESTMENT OF GREEN TECHNOLOGIES , Proceedings of Annual Conferences of NPUA: Vol. 2 (2025)
T.A. BARSEGHYAN, K.G. AVETISYAN, DESIGNING AN AGRICULTURAL ADVISORY SYSTEM USING MACHINE LEARNING , Proceedings of Annual Conferences of NPUA: Vol. 1 (2024)

1-10 of 72 Next

You may also start an advanced similarity search for this article.