SELECTING THE VARIANT OF HYDROSTATIC CHASSIS OF A WHEEL MACHINE FOR STONE QUARRYING

Authors

S.S. HARUTYUNYAN National Polytechnic University of Armenia Author
J.A. ASATRYAN National Polytechnic University of Armenia Author

Keywords:

machine for stone quarrying, hydrostatic chassis, circular saw, cutting head

Abstract

The analysis of variants of the hydrostatic chassis of a wheel machine for quarrying wall stone of the correct form based on the truck is introduced. The most profitable option of choice of hydraulic units for manufacturing prototype machine is considered.

Downloads

pdf

Published

22.07.2026

Issue

Section

Articles

Most read articles by the same author(s)

J.A. ASATRYAN, WAYS FOR DEVELOPING MACHINES FOR QUARRYING STONE OF THE CORRECT FORM , Proceedings of Annual Conferences of NPUA: Vol. 2 (2019)
J.A. ASATRYAN, S.S. HARUTYUNYAN, F.A. MSRYAN, A.V. BAGHDASARYAN , TECHNOLOGICAL OPPORTUNITIES FOR THE SECONDARY USE OF ABANDONED QUARRIES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2021)
S.S.. HARUTYUNYAN, J.A. ASATRYAN, OPTIMAL CONSTRUCTION OF А WHELLED MACHINE FOR QUARRYING WALL STONE OF THE CORRECT FORM , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
J.A. ASATRYAN, S.S. HARUTYUNYAN, O.V. ENGOYAN, NEW CONSTRUCTIONS OF DISC SAWS OF HIGH ACCURACY FOR STONE QUARRYING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2016)

Similar Articles

S.S.. HARUTYUNYAN, J.A. ASATRYAN, OPTIMAL CONSTRUCTION OF А WHELLED MACHINE FOR QUARRYING WALL STONE OF THE CORRECT FORM , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
J.A. ASATRYAN, WAYS FOR DEVELOPING MACHINES FOR QUARRYING STONE OF THE CORRECT FORM , Proceedings of Annual Conferences of NPUA: Vol. 2 (2019)
J.A. ASATRYAN, S.S. HARUTYUNYAN, O.V. ENGOYAN, NEW CONSTRUCTIONS OF DISC SAWS OF HIGH ACCURACY FOR STONE QUARRYING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2016)
J.A. ASATRYAN, S.S. HARUTYUNYAN, F.A. MSRYAN, A.V. BAGHDASARYAN , TECHNOLOGICAL OPPORTUNITIES FOR THE SECONDARY USE OF ABANDONED QUARRIES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2021)
A.M. ARZUMANYAN, T.A. MIRVELYAN, CALCULATION OF CUTTING STRENGTH AT PROCESSING OF ALLOYS FROM NON-FERROUS METALS BY CORUNDUM CUTTING PLATES WITH SQUARE-CUTTING CUTTING LOOP , Proceedings of Annual Conferences of NPUA: Vol. 2 (2018)
L.H. MUTAFYAN, R.E. AVAGYAN, THE IMPACT OF THE CUTTING CONDITIONS ON THE CUTTING TOOL WEAR AT TREATING HARD-PROCESSED MATERIALS AT INTERRUPTED CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
H.B. BAGHDASARYAN , M.Y. HARUTYUNYAN, V.H. BAGHDASARYAN , IMPACT OF CUTTING MODES ON THE FORMATION OF TECHNOLOGICAL RESIDUAL STRESSES AT BLADE CUTTING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
B.A. BALASANYAN, A.L. ARSHAKYAN, S.H. HAKOBYAN, B.S. BALASANYAN, A PROGRAM FOR CALCULATING THE CUTTING DEPTHS OF THE STAGES OF A MULTI-STAGE DRILL FROM THE EQUALITY CONDITION OF THE PRODUCTS OF THEIR TORQUES AND AXIAL FORCES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2023)
D.G. YURMUZYAN, G.A. SIMONYAN, INVESTIGATING THE CUTTING PROCESS WITH A MULTISTEPPED BLADE CUTTER THROUGH THREE-DIMENSIONAL MODELING , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
A.R. HOVHANNISYAN, A.R. KOSTANDIAN, N.K. MANASYAN, CIRCULAR ECONOMY IN THE CONTEXT OF INVESTMENT OF GREEN TECHNOLOGIES , Proceedings of Annual Conferences of NPUA: Vol. 2 (2025)

1-10 of 76 Next

You may also start an advanced similarity search for this article.