INVESTIGATING THE STRESS-STRAIN STATE OF PRINTING CYLINDERS IN THE CONTACT ZONE

Authors

A.A. MARGARYAN National Polytechnic University of Armenia Author

Keywords:

ofset cylinder, typan, elastic working surface, stress-strain state, relative displacements

Abstract

The stress-strain state occurring in the surface layers of hard and elastic printing cylinders working surfaces, as well as the statics and dynamics of deformations and the relative displacements in the contact zones are considered, taking into account the stiffness, by whose generalised results, it is possible to ensure the printing quality in the contact zones.

Downloads

pdf

Published

29.06.2026

Issue

Section

Articles

Most read articles by the same author(s)

A.A. MARGARYAN, DEPENDENCE OF THE INK LAYER OBTAINED BY THE METHOD OF SCREEN PRINTING ON THE LINEARITY OF THE MESH , Proceedings of Annual Conferences of NPUA: Vol. 1 (2021)
A.A. MARGARYAN, N.S. TOVMASYAN, OBTAINING IMAGES IN CMYK COLOR MODEL WITH GRIDS OF DIFFERENT LINEARITY USING THE SILK PRINTING METHOD , Proceedings of Annual Conferences of NPUA: Vol. 1 (2023)
A.A. MARGARYAN, S.V. VERLINSKI, STUDYING THE STRAIN-STRESS STATE IN THE CONTACT OF PRINTING CYLINDERS BY THE METHOD OF FINITE ELEMENTS , Proceedings of Annual Conferences of NPUA: Vol. 2 (2018)

Similar Articles

A.A. MARGARYAN, S.V. VERLINSKI, STUDYING THE STRAIN-STRESS STATE IN THE CONTACT OF PRINTING CYLINDERS BY THE METHOD OF FINITE ELEMENTS , Proceedings of Annual Conferences of NPUA: Vol. 2 (2018)
A.H. DAVTYAN, COMPUTER SIMULATION OF DRAWING A RECTANGULAR SECTION SAMPLE IN A WEDGE-SHAPED DIE AT DIFFERENT ANGLES OF INCLINATION OF THE WEDGE , Proceedings of Annual Conferences of NPUA: Vol. 1 (2021)
A.M. ARZUMANYAN, T.A. MIRVELYAN, CALCULATION OF CUTTING STRENGTH AT PROCESSING OF ALLOYS FROM NON-FERROUS METALS BY CORUNDUM CUTTING PLATES WITH SQUARE-CUTTING CUTTING LOOP , Proceedings of Annual Conferences of NPUA: Vol. 2 (2018)
M.G. STAKYAN, M.S. TOROSYAN, H.A. GHAZARYAN, MODERN TECHNOLOGIES OF STRENGTHENING THE WELDED SEAMS OF THIN -WALL PIPELINES , Proceedings of Annual Conferences of NPUA: Vol. 1 (2021)
S.G. YESAYAN, SPECIFING THE ANALYTICAL LINK OF STRAIN-STRESS COUSIDERING THE MEDICEM CREEP , Proceedings of Annual Conferences of NPUA: Vol. 2 (2017)
N.H. HAKOBYAN, A.N. BAGHDASARYAN , DEVELOPING THE EXOSKELETON ACTIVE MODULE BY USING PIEZOELECTRIC WAVE VIBROMOTOR , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
S.S. MARTIROSYAN, INVESTIGATION AND ANALYSIS OF PRESSURE AND DEFORMATION IN THE PRINTING ZONE , Proceedings of Annual Conferences of NPUA: Vol. 1 (2023)
G.L. PETROSYAN, A.H. DAVTYAN, INVESTIGATING THE DRAWING PROCESS OF A RECTANGULAR SECTION SINTERED SAMPLE IN A WEDGE-SHAPED DIE , Proceedings of Annual Conferences of NPUA: Vol. 2 (2020)
G.L. PETROSYAN, N.G. HAKOBYAN, A SIMPLIFIED METHOD FOR DETERMINING THE STRESSES ON FREE SURFACES OF A CURVED WIDE STRIP , Proceedings of Annual Conferences of NPUA: Vol. 2 (2019)
H.S. CHIBUKHCHYAN, P.YU. GASPARYAN, RESEARCH OF IMPROVEMENT OF MECHANICAL PROPERTIES OF THIN-WALLED PARTS USED IN AVIATION TECHNOLOGY , Proceedings of Annual Conferences of NPUA: Vol. 1 (2022)

1-10 of 176 Next

You may also start an advanced similarity search for this article.